HSU Research Forum (HRF)  

Go Back   HSU Research Forum (HRF) > Hsu Central > Hsu Research - Speakers and Subwoofers
Forum Help Members List Calendar Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Rate Thread Display Modes
  #1  
Old October 25th, 2011, 9:26 AM
Andrew879 Andrew879 is offline
Registered User
 
Member Since: Oct 2011
Posts: 4
Andrew879 is on a distinguished road
Vtf3 mk3 popping

First off I thought maybe my vtf3 mk3s gain was to high but when I purchased my vtf3 mk4 I noticed it wouldn't pop but the mk3 would so its not the signal any suggestions? I've noticed its mainly on lower notes and mainly happens with explosions and helicopter sounds
Reply With Quote
  #2  
Old October 25th, 2011, 12:04 PM
bread29 bread29 is offline
Registered User
 
Member Since: Jul 2010
Location: Norfolk, VA
Posts: 4
bread29 is on a distinguished road
I had the exact same problem when I first received the MK3. The sub is most likely being stressed during those "explosions" and bottoming out. I turned the Level down in the receiver and the problem went away.
Reply With Quote
  #3  
Old October 25th, 2011, 1:03 PM
Andrew879 Andrew879 is offline
Registered User
 
Member Since: Oct 2011
Posts: 4
Andrew879 is on a distinguished road
I just don't see why the mk4 wouldn't and the mk3 would. I have the mk4 a little higher and I used a radioshack DB meter. One other thing what should I set the Q to on the mk4 to match the mk3?
Reply With Quote
  #4  
Old October 25th, 2011, 1:49 PM
Pete_Hsu Pete_Hsu is offline
Hsu Research
 
Member Since: Dec 2004
Location: Orange County, CA
Posts: 4,212
Pete_Hsu will become famous soon enoughPete_Hsu will become famous soon enough
Hi Andrew,

Have you tried gain matching each subwoofer? What you have to do is start with one subwoofer in one fixed location (with crossover 'Out', bass extension switch in the down position, phase '0', volume knob 1/4 of the way up). Set your A/V receiver master volume level to a moderate level that you would normally use during music playback. Place the sound level meter at a fixed location (say, 1 foot away from the front of the subwoofer?). Play track 14 on the Test CD. Write down the SPL that is shown on the meter. Then move out the first subwoofer and put the second subwoofer in the exact same location as the first subwoofer. Set everything the same on the subwoofer amplifier (with Q = 0.7 on the VTF-3 MK4), and adjust the volume knob until the sound pressure level is the same as the first subwoofer when playing track 14 on the Test CD.

Then you can move each subwoofer into place.

Note that you may have to reduce the subwoofer channel level on your A/V receiver. When using two subwoofers, the combined level will generally be ~ 3-6dB higher than a single subwoofer, so you can adjust the subwoofer channel level on the A/V receiver to compensate.

Do make sure that each subwoofer is in phase with each other (ie. when you play one subwoofer and then turn on the second subwoofer, then sound pressure level should increase rather than decrease). Then you can flip the phase switch on both units to see if the subwoofers are in phase with the main speakers.

Sincerely,
__________________
Pete - Hsu Research
Reply With Quote
  #5  
Old February 12th, 2012, 5:04 PM
Andrew879 Andrew879 is offline
Registered User
 
Member Since: Oct 2011
Posts: 4
Andrew879 is on a distinguished road
thanks i wasnt even thinking i guess. i was measuring from my main seating location i should have known the room would alter the db of each sub at different locations i will do the test and reply with my results
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes Rate This Thread
Rate This Thread:
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off
Forum Jump
 


All times are GMT -8. The time now is 11:59 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Forum Rules The Golden Rule: Treat others as you would want to be treated.

Technical Support: The best way to get tech support for serious issues is to call or email us. Questions asked on the forum may not be answered by qualified professionals.

No "Flaming": Spiteful talk and flaming wars will lead to "time-outs" for parties involved.

Shootouts: Shootouts are comparisons between products. We need to know about shootouts before allowing them on the forum, so call us and talk to the director of Sales before posting. Otherwise, your shootout may be removed.

Add to Reputation: Once you are a registered member, you can click this icon to add to the tally of other members' Rep Points. You must vote for seven other people before you can vote for the same person twice.

Report Bad Posts: Once you register, click this icon to let Administrators know if they should review a post. Please be specific as to why action might be needed.

HSU RESEARCH IS NOT RESPONSIBLE FOR COMMENTS MADE BY THIRD PARTY INDIVIDUALS ON THIS FORUM.

Thanks for reading the rules. Have a good time :)

In Association With